- Szerokie możliwości modyfikacji
- Konstrukcja bazująca na kultowym modelu Prusa MK3s
- Możliwość drukowania zamiennych części konstrukcyjnych
Remake3D MK3s - kompletny zestaw DIY do budowy drukarki 3D, inspirowanej konstrukcją Original Prusa i3 MK3s.
Zestaw do budowy drukarki Remake3D MK3s jest starannie dobranym zbiorem części pochodzących od najlepszych producentów, również od dostawców firmy Prusa.
W naszej wersji staraliśmy się poprawić wszystkie błędy i niedociągnięcia Original Prusa MK3s. Konstrukcja posiada znacznie lepszą technikę liniową oraz części lepszej jakości, w tym: łożyska liniowe MISUMI, oryginalne paski firmy GATES USA, sztywną ramę z profili aluminiowych Full Bear Upgrade oraz naszą głowicę Premium V6 - równoważną do tej pochodzącej z oryginału.
Remake3D MK3s - kompletny zestaw DIY do budowy drukarki 3D, inspirowanej konstrukcją Original Prusa i3 MK3s.
Zestaw do budowy drukarki Remake3D MK3s jest starannie dobranym zbiorem części pochodzących od najlepszych producentów, również od dostawców firmy Prusa.
W naszej wersji staraliśmy się poprawić wszystkie błędy i niedociągnięcia Original Prusa MK3s. Konstrukcja posiada znacznie lepszą technikę liniową oraz części lepszej jakości, w tym: łożyska liniowe MISUMI, oryginalne paski firmy GATES USA, sztywną ramę z profili aluminiowych Full Bear Upgrade oraz naszą głowicę Premium V6 - równoważną do tej pochodzącej z oryginału.
- Typ silnika
- NEMA17
- Typ drukarki
- FFF / FDM
- Napięcie zasilania
- 24V
- Kolor
- Lime Green
Lion Orange
Yellow Bahama - Średnica filamentu
- 1,75mm
- Waga
- 10 kg
- Pojemność pamięci
- 16 GB
- Płyta główna
- Einsy Rambo 1.1a
- Części drukowane
- Tak
Remake3D MK3s - kompletny zestaw DIY do budowy drukarki 3D, inspirowanej konstrukcją Original Prusa i3 MK3s.
Zestaw do budowy drukarki Remake3D MK3s jest starannie dobranym zbiorem części pochodzących od najlepszych producentów, również od dostawców firmy Prusa.
W naszej wersji staraliśmy się poprawić wszystkie błędy i niedociągnięcia Original Prusa MK3s. Konstrukcja posiada znacznie lepszą technikę liniową oraz części lepszej jakości, w tym: łożyska liniowe MISUMI, oryginalne paski firmy GATES USA, sztywną ramę z profili aluminiowych Full Bear Upgrade oraz naszą głowicę Premium V6 - równoważną do tej pochodzącej z oryginału.
- Typ silnika
- NEMA17
- Typ drukarki
- FFF / FDM
- Napięcie zasilania
- 24V
- Kolor
- Lime Green
Lion Orange
Yellow Bahama - Średnica filamentu
- 1,75mm
- Waga
- 10 kg
- Pojemność pamięci
- 16 GB
- Płyta główna
- Einsy Rambo 1.1a
- Części drukowane
- Tak
Sklep oczywiście w miarę możliwości pomocny części zamienne wysyłają natychmiast
Cała technika liniowa działa ZNACZĄCO lepiej niż w oryginalnej MK3, cicha, bez wibracji po prostu tak jak powinno być. INstrukcja wymaga aktualizacji jednak support ze strony sklepu nadrabia jej brak.
As I want continuity on 3D printing, in particular when the pressure gets high to get prints done in a tight timeframe, I needed a second 3D printer. Tried to make a kit myself, and when googling various sites so I came across the offer of Hobby Store in Poland. They offer a very nice kit against a very acceptable price point with top quality components like rods and linear bearings from MISUMI, stepper motors from Fysetc, a full BEAR upgrade and very important; a drop in replacement of the RAMBO Einsy board. This is very important is this controller board accepts the original firmware of the Prusa MK3S.
I was anxious to see the arrival of the kit. Everything was packed very well, although an accompanying full BOM list would have been helpful to check if the kit is complete. That this is important was proven during the build of the printer. However, all components are packed very well. For assembly one could easily use the instructions from the Prusa site. The BEAR upgrade is of course different but not that difficult. Furthermore the kit comes with upgraded printed 3D parts (if ordered so) that are an improvement over the Prusa kit. The Y-rod mounts are much better (no tiewraps to hold the rods in place but a decent clamps to tighten the rods on the BEAR frame. Better Bearing claps for the Z-axis also with integrated belt tensioning mechanism for the X-axis. For let’s say 80-90% of the assembly the instructions from the Prusa site can be used. However, there are slight differences but not that hard to find out yourself. I for instance needed assistance for wiring the power supply and protection board of it. Sending an email to Hobby story got replied to withing 24 hours. Now back to the missing BOM list. During assembly I found out there were parts missing. So when sending an email with the description of the missing parts it resulted in express delivery of those parts to my house. A very good service as shipment from Poland to the Netherlands is not that simple.
When the printer mechanically was ready it took me some time to get it running for personal reasons. After this delay I sat down and connected everything from heated bed, extruder, stepper motors, Power Supply Unit and so on to the RAMBO Einsy board. Switched on the Power supply and a la, the Remake MK3s 3D printer was ready to be calibrated. Calibration was easily performed once you went to the procedure of the original Prusa, although the printer itself guides you through the various steps.
It is really a relief printing wit the REMAKE Pruse. It is quit, stable and gives excellent result directly after calibration. I have not done very exhaustive tests yet put will in time come back with updates.
Thanks to the team of Hobby Store in Poland and the excellent job they did on putting together this fabulous kit.
Klienci, którzy kupili ten produkt nabyli także:
I'm still very glad that i bought one.